ProStart CT-5072 Installationsanleitung

Notice The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either d

P. 10 Installation Guide clutch switch to the starter motor. When the key is turned to the start position without pressing the pedal, you will tes

Installation Guide P. 11 Harness Description When connecting the Module, it is important to make sure the connector with the Ground wire is connecte

P. 12 Installation Guide 5-Pin Secondary Harness Wire Description 1 BLACK (–) Chassis ground input This wire must be connected to bare, unpainted

Installation Guide P. 13 Wire Description 5 WHITE / GREEN (–) Disarm output 500 mA ground output when the button is pressed. This wire is for di

P. 14 Installation Guide Wire Description 12 YELLOW (+) Glow-plug input This positive input will monitor the Glow Plug Light in Diesel Mode: it w

Installation Guide P. 15 Wire Description 4 BLACK/ BROWN (–) Priority door output only Gives a negative pulse on the second press of the button.

P. 16 Installation Guide Manual or Automatic Transmission This module may be installed on vehicles with manual or automatic transmissions. It is o

Installation Guide P. 17 3. Press and hold the button and keep it down until the siren chirps twice. 4. The transmitter has been stored in memor

P. 18 Installation Guide Note: For vehicles that require the ignition to be turned ON to activate the brake, follow these steps: a. After flashi

Installation Guide P. 19 3. Press the button if you wish to increase the time delay or the button if you want to decrease it. The time delay wi

P. 2 Installation Guide Table of Contents Introduction ... 3 Included in the Pac

P. 20 Installation Guide 4. Once the engine is running at normal idle speed, press the brake pedal and keep it down until you hear the siren chir

Installation Guide P. 21 3. Within 20 sec. of engaging the parking brake, press and hold , or on the transmitter. The parking lights will flas

P. 22 Installation Guide Installation-programmable Features The following features can be programmed according to the needs of the installation an

Installation Guide P. 23 AUX 2 Note: This 500 mA negative Aux 2 output can be used for many different applications OPTION 1 Car Finder. The siren w

P. 24 Installation Guide Turbo Mode If Turbo Mode is configured at installation, it will allow a turbocharger to idle down after the user leaves t

Installation Guide P. 25 Option 3: Open Zone Notification: if a Door is detected as open 10 sec. after arming, the Siren/Horn will sound 3 times

P. 26 Installation Guide Note: For Hardware 5.0 and higher, there can only be one bypass connected to the unit. Multi-car Operation This option a

Installation Guide P. 27 6 • A tach signal is detected before Ignition. 10 • Hood wire is active. Note: The installer can also use the PRG-100 to

P. 28 Installation Guide Closing Up Use tie-wraps or screws to properly secure the starter module and keep the wiring away from any moving parts s

Installation Guide P. 29 Troubleshooting Q & A The following are some common installation related issues. A problem or symptom is given and then

Installation Guide P. 3 Introduction This guide contains all the information relevant and necessary for the installation of the alarm and remote sta

P. 30 Installation Guide 12. The car starts, the heater works but not the air conditioning system. • Missing second accessory (common on some For

P. 4 Installation Guide • The Programming Assistance Button (a.k.a. PAB): The PAB is mounted on the side of the unit. This push button mimics th

Installation Guide P. 5 Installation Order The following is a suggested order for the Installation procedure. It is intended as a guide for novices,

P. 6 Installation Guide • Return to the engine bay and route the tach and hood pin wire to their corresponding connections. • Solder the engine

Installation Guide P. 7 Quenching Diodes It was said earlier that a relay energizes itself by applying positive from the battery to either 85 or 86

P. 8 Installation Guide The Relay Connections 85: Connects to the +12 volt park light output from the remote start module. This becomes the positi

Installation Guide P. 9 Comments: At rest the relay is not active, and +12 volts on the starter wire passes through the relay (through 87A & 30)